2004 PREVAILING WAGE RATES
     CLARK COUNTY

DATE OF DETERMINATION: October 1, 2003

APPLICABLE FOR PUBLIC WORKS PROJECTS BID/AWARDED
OCTOBER 1, 2003 THROUGH SEPTEMBER 30, 2004*

*Pursuant to NAC 338.040(3), "After a contract has been awarded, the prevailing rates of wages
in effect at the time of the opening of bids remain in effect for the duration of the project."

_________________________________________________________________

Job Descriptions for Recognized Classes of Workmen

        Regarding job descriptions for public works projects, please take notice of the following:

1. Pursuant to NAC 338.0095(1)(a), "A workman employed on a public work must be paid based on the type of work that the workman actually performs on the public work and in accordance with the recognized class of the workman."

2. The work description for a particular class is not intended to be jurisdictional in scope nor to be construed as limiting or prohibiting any worker from performing the work of one or more classes.

3. Any person who believes that a type of work is not classified, or who otherwise needs clarification pertaining to the recognized classes or job descriptions, shall contact the Labor Commissioner, in writing,  for a determination of the applicable classification and pay rate for a particular type of work. 

4. The job descriptions set forth or referenced herein supercede any and all descriptions previously agreed upon by the Labor Commissioner in any settlement agreements or stipulations arising out of contested matters. 

5. The following specific provisions, where applicable, shall prevail over any general provisions of the job descriptions:

• Amendments to the prevailing wage determinations;

• Group Classifications and/or descriptions included with wage determinations for a particular type of work in a particular county.                    

AIR BALANCE TECHNICIAN, includes but is not limited to:
Inspecting, testing, programming, documenting, adjusting and balancing heating, cooling and ventilating systems using specialized tools and testing equipment to attain performance standards specified in the design of the systems.

ALARM INSTALLER, includes but is not limited to:

1. Installing or testing electrical protective signaling systems used to provide notification of fire, burglary or other irregularities on the premises of the subscriber of the system;
2. Installing of wiring and signaling units;
3. Repairing electrical protective signaling systems
4. Starting up, programming and documenting systems;

BOILERMAKER, includes but is not limited to:

1. Constructing, assembling, maintaining and repairing stationary steam boilers and boiler house auxiliaries;
2. Aligning structures or plate sections to assemble boiler frame tanks or vats;
3. Assisting in the testing of assembled vessels, directing cleaning of boilers and boiler furnaces;
4. Inspecting and repairing boiler fittings, including, without limitation, safety valves, regulators, automatic-control mechanisms, water columns and auxiliary machines.

BRICKLAYER, includes but is not limited to:

1. Laying materials, including without limitation, brick, structural tile and blocks of concrete, cinder, glass, gypsum and terra cotta, but not including stone, to construct or repair walls, partitions, arches, sewers, and other structures;
2. Laying and aligning bricks, blocks or tiles to build or repair structures for high temperature equipment, including, without limitation, cupola, kilns, ovens and furnaces; and
3. Fastening or fusing brick or other building materials to structures with wire clamps, anchor holes, torches or cement.

CARPENTER, includes but is not limited to:

1. Laying out, constructing, erecting, fabricating, installing and repairing structures and fixtures of wood, plywood, or alternative materials, doors and hardware and the fastening of the same, inclusive of garage or overhead door openers, cabinets, framework, floors, and acoustical ceiling systems using carpenter's hand tools and power tools;
2. Installing or erecting metal studs, drywall, lathing, wall partitions, prefabricated EFIS panels or any other system of panels that is attached to the interior or exterior of any building or structure, insulation and all types of ceilings;
3. Pre-cast concrete and concrete form work which includes but is not limited to: setting of templates, layout, fabrication, constructing, placing, erection, rigging and hoisting, stripping and removing of all forms which are to be reused;
4. Plywood decking, including, without limitation, stacking and installation of the plywood and the plywood decking;
5. Cutting, setting, removing of beam sides and soffits, bracing, and pads;
6. Constructing all wood panel forms and frame wall;
7. Building, erecting and disassembling self-supporting scaffolds that are more than 14 feet in height;
8. Laying out, cutting, joining, fitting of Foam Architectural Elements if same are attached mechanically; and
9. Shaping, cutting and planing by any means if done by hand or machine.

CEMENT MASON, includes but is not limited to:

1. Smoothing and finishing surfaces of poured concrete floors, walls, sidewalks and curbs to specified textures;
2. Patching holes with fresh concrete or an epoxy compound;
3. Molding expansion joints and edges through the use of edging tools, jointers and straightedges;
4. Setting of curb and gutter forms one board high;

ELECTRONIC COMMUNICATION INSTALLER/TECHNICIAN, includes but is not limited to:

1. Pulling cable, installing and trimming devices, terminating loops, circuits, or other data gathering points;
2. Termination of main control panels, racks, or other head end equipment, as well as testing of all circuits from the field devices to the main control panels and/or equipment;
3. Utilizing test equipment for the purpose of troubleshooting and verifying the integrity of the circuits in question;
4. Using hand tools to assemble and install data communication lines and equipment computer systems, antennas and towers;
5. Disassembling equipment to adjust, repair or replace parts using hand tools;
6. Starting up, programming and documenting systems;
7. Measuring, cutting, splicing, connecting, soldering and installing wire and cable associated with communication systems

ELECTRONIC COMMUNICATION SENIOR INSTALLER/TECHNICIAN, includes but is not limited to:

May include the duties of the Installer/Technician; working with, supervising, and coordinating the work of the Installer/Technician.

ELECTRICIAN LINEMAN, includes but is not limited to:

1. Erecting and repairing wood poles and prefabricated light duty metal towers, cable and related equipment to construct overhead transmission and distribution power lines used to conduct electrical energy between generating stations, substations and consumers;
2. Directing and assisting electrician ground men in attaching cross arms, insulators, lightning arresters, switches, wire conductors and auxiliary equipment to poles and towers in preparation of erecting the poles or towers;
3. Climbing erected poles or towers and installing equipment such as transformers
4. Strings wire conductors between erected poles with assistance of ground helpers and adjusts slack in conductors to compensate for contraction and elongation of conductors due to temperature variations, using winch.

ELECTRICIAN GROUNDMAN, includes but is not limited to:

1. Working under the direct supervision of linemen, including the operation of jackhammers and man hauls;
2. Loading and unloading of materials and equipment used by electrician lineman.
3. Does not include climbing poles, towers or other structures or working in the proximity of energized lines or equipment;

ELECTRICIAN-NEON SIGN, includes but is not limited to:

1. Installing, servicing and repairing plastic, neon and illuminated signs;
2. Ascending ladders or operating hydraulic or electric hoist to install, service, or examine sign to determine cause of malfunction;
3. Wiring, rewiring or removing defective parts and installing new parts using electrician's tools;
4. Removing sign or part of sign for repairs, such as structural fabrication, scroll repair, or transformer repair;

ELECTRICIAN WIREMAN, includes but is not limited to:

1. Laying out plans, installing, testing and repairing wiring, electrical fixtures, apparatus and control equipment;
2. Measuring, cutting, bending, threading, assembling and installing electrical conduit by using tools including, without limitation, a hacksaw, pipe threader, or conduit bender;
3. Pulling wiring through conduit;
4. Splicing wires;
5. Connecting wiring to lighting fixtures and power equipment;
6. Installing control and distribution apparatus, including, without limitation, switches, relays and circuit breakers, and fastening such apparatus into place;
7. Connecting power cables to equipment, including, without limitation, electric ranges and motors, and installing grounding leads;
8. Testing the continuity of a circuit to ensure electrical compatibility and safety of components using testing instruments, including, without limitation, an ohmmeter, a battery and buzzer, and an oscilloscope;
9. As necessary, cutting and welding steel structural members;

ELEVATOR CONSTRUCTOR, includes but is not limited to:

1. Assembling, installing, repairing and maintaining electric and hydraulic freight and passenger elevators, escalators and dumbwaiters;
2. Cutting pre-fabricated sections of framework, rails and other elevator components to specified dimensions, using acetylene torch, power saw, and disc grinder;
3. Installing cables, counterweights, pumps, motor foundations, escalator drives, guide rails, elevator cars, and control panels, using hand tools;

FENCE ERECTOR, includes but is not limited to:

1. Erecting or repairing chain link, wooden, tortoise, wire/wire mesh, or temporary fencing;
2. Mixing and pouring concrete around bases of posts and tamping soil into post hole to embed post;
3. Digging post holes with a spade, post hole digger or power driven auger;
4. Aligning posts through the use of lines or by sighting;
5. Verifying vertical alignment of posts with a plumb bob or spirit level;

FLAG PERSON, includes but is not limited to:

1. Directing movement of vehicular traffic through construction projects;
2. Distributing traffic control signs and markers along site in designated pattern;
3. Informing drivers of detour routes through construction sites;

FLOOR COVERER, includes but is not limited to:

1. Applying blocks, strips or sheets of shock-absorbing, sound-deadening or decorative covering to floors and walls, including carpets or rugs;
2. Measuring and cutting covering materials, such as rubber, linoleum, astro-turf, or cork tile and foundation material such as felt, using rule, straightedge, linoleum knife and snips;
3. Spreading adhesive cement over floor to cement foundation material to floor for sound-deadening, and to prevent covering from wearing at the board joints;
4. Rolling finished floors to smooth the floor and press cement into base and covering;
5. Fitting of devices for the attachment of carpet, linoleum, rubber and all resilient floor coverings and the fitting of metal edges, corners and caps used in the installation of the foregoing materials and all other preparatory work;

GLAZIER, includes but is not limited to:

1. Installing, setting, cutting, preparing, or removal of glass, or materials used in lieu thereof, including, without limitation, in windows, doorways, showers, bathtubs, skylights and display cases;
2. Installing glass on surfaces, including, without limitation, fronts of buildings, interior walls and ceilings;
3. Installing pre-assembled framework for windows and doors designed to be fitted with glass panels, including stained glass windows by using hand tools;
4. Loading and arranging glass, or materials used in lieu thereof,  on trucks at the site of the public work;

HIGHWAY STRIPER, includes but is not limited to:

1. Painting highways, streets and parking surfaces by using manually propelled or mechanically propelled machines, brushes, rollers or spray guns;
2. Installing any device or application of any material used in lieu of paint for traffic direction, including, without limitation, buttons, tapes, plastics, rumble bars and other similar materials;

HOD CARRIER-BRICK MASON, includes but is not limited to:

1. Tending to or assisting brick masons, bricklayers and stonemasons;
2. Mixing, packing, wheeling and tempering mortar and fire clay;
3. Mixing, supplying and holding materials or tools;
4. Mixing, handling and conveying all other materials used by brick masons, bricklayers and stone masons;
5. Building scaffolds, trestles, boxes and swinging staging used exclusively by bricklayers and stone masons;
6. Hanging cables and placing putlogs;
7. Carrying bricks and mortar in a hod;
8. Cleaning work area and equipment of bricklayers and stone masons

HOD CARRIER-PLASTERER TENDER, includes but is not limited to:

1. Serving Plasterers in any capacity;
2. Handling materials after the materials are delivered as used by a Plasterer;
3. Building and handling all necessary trestle, scaffolding and planking of scaffolding for the exclusive use of Plasterers;
4. Building mortar boxes, mortar boards and stands.

IRONWORKER, includes but is not limited to:

1. Performing duties, as part of a crew, to raise, place and unite girders, columns and other structural steel members to form completed structures or structure frameworks;
2. Setting up hoisting equipment for raising and placing structural steel members;
3. Fastening steel members to cable of hoist, using chains, cable or rope;
4. Forcing steel members into final position using turnbuckles, crowbars, jacks, hand tools;
5. Aligning rivet holes in steel members with corresponding holes in previously placed steel members by driving drift pins to handle of wrench through holes;
6. Bolting aligned steel members to keep them in position until the steel members can be permanently riveted, bolted or welded into place;
7. Cutting and welding steel members;
8. Installing and repairing gates, iron doors, flagpoles, iron fences and roof decking;
9. Installing corrugated sheets when attached to steel frames;
10. Stud welding of all iron, steel and metal to structural steel;
11. Handling and setting of steel and metal joists;
12. Loading, unloading, hoisting, handling, signaling, placing and erecting of pre-stressed and pre-cast materials;
13. Handling, racking, sorting, cutting, bending, hoisting, placing, burning, welding and tying all material used to reinforce concrete construction;

LABORER:

Group 2
Asphalt raker, ironer, spreader, luteman
Buggymobile man
Cement dumper (on one yard or larger mixers & handling bulk cement)
Cesspool digger and installer
Chucktender (except tunnels)
Concrete core cutter
Concrete curer, impervious membrane and oiler of all materials
Concrete saw man, excluding tractor type, cutting, scoring old or new concrete
Gas and oil wrapper, pot tender and form man
Making and caulking of all non-metallic pipe joints
Operators and tenders of pneumatic and electric tools, vibrating machines, hand propelled trenching machines, impact wrench multiplate and similar mechanical tools not separately classified herein
Operator of cement grinding machine
Riprap stonepaver
Roto-scraper
Sandblaster (pot tender)
Scaler
Septic tank digger and installer (lead man)
Tank scaler and cleaner
Tree climber, faller, chain saw operator, Pittsburgh chipper and similar type brush shredders

Group 3
Cutting torch operator
Gas and oil pipeline wrapper
Gas and oil pipeline laborer, certified
Jackhammer and/or pavement breaker
Laying of all non-metallic pipe, including landscape sprinklers, sewer pipe, drain pipe and underground tile 
Mudcutter
Concrete vibrator operator, all sizes
Rock slinger
Scaler (using bos'n chair or safety belt or power tools)
Forklift (Incidental to Trade) – A journeyman shall hold OSHA certification at time of referral

Group 4
Cribber or shorer, lagging, sheeting, trench bracing, hand guided lagging hammer
Head rock slinger
Powderman-blaster, all work of loading holes, placing and blasting of all powder and explosives of whatever type, regardless of method used for such  loading and placing
Sandblaster (nozzleman)
Steel header-board man

Group 5
Driller (core, diamond or wagon)
Joy driller model TW-M-2A, Gardner-Denver model DH 143 and similar type drills (in accordance with Memorandum of Understanding between Laborers and Operating Engineers dated Miami, Florida, February 3, 1954)
Gas and oil pipeline fusion
Gas and oil pipeline wrappers, 6" pipe and over

Group 6
Miner and Bullgang

Group 7
Asbestos Abatement
Lead Abatement
Hazardous Waste Abatement
Petro-Chemical Abatement
Radiation Remediation
Microbial Remediation

MARBLE MASON, includes but is not limited to:

1. Cutting, tooling, and setting marble slabs in floors and walls of buildings and renovating and polishing marble slabs previously set in buildings;
2. Trimming, facing and cutting marble to a specific size using a power saw, cutting and facing equipment, and hand tools
3. Drilling holes in marble slabs and attaching brackets;
4. Spreading mortar on the bottom and sides of a marble slab and on the side of adjacent marble slabs;
5. Setting blocks in positions, tamping a marble slab into place and anchoring bracket attachments with wire;
6. Filling joints between marble slabs with grout and removing excess grout with a sponge;
7. Cleaning and beveling cracks and chips on marble slabs using hand tools and power tools;
8. Heating cracked or chipped areas of a marble slab with a blowtorch and filling the defect with a composition mastic that matches the grain of the marble slab; and
9. Polishing marble slabs and other ornamental stone to a high luster by using hand tools and power tools.

MECHANICAL INSULATOR, includes but is not limited to:

1. Covering and lining structures with cork, canvas, tar paper, magnesia and related materials;
2. Installing blown-on insulation on pipe and machinery;
3. Lining of mechanical room surfaces and air handling shafts;
4. Filling and damming of fire stops and penetrations including, but not limited to, electrical and mechanical systems;
5. Foam applications for the purpose of thermal, acoustical, or fire protective purposes, including RTV foams or equivalents, applied to mechanical or electrical systems;
6. Duct lining and duct wrapping, direct application and installation of fire protection of grease ducts, exhaust systems, or any other ductwork for acoustical or thermal purposes;
7. Insulation of field joints on pre-insulated underground piping and the pouring of Gilsilite or its equivalent;
8. The application of material, including metal and PVC jacketing, on piping, fittings, valves, flanges, boilers, ducts, plenums, flues, tanks, vats, equipment and any other hot or cold surface for the purpose of thermal control;

MILLWRIGHT, includes but is not limited to:

1. Installing machinery and equipment according to layout plans, blueprints and other drawings in industrial establishments by using hoists, lift trucks, hand tools and power tools;
2. Dismantling machines by using hammers, wrenches, crowbars and other hand tools;
3. Assembling and installing equipment, including, without limitation, shafting, conveyors, monorails and tram rails, by using hand tools and power tools;
4. Constructing foundations for machines by using hand tools and building materials, including, without limitation, wood, cement and steel;
5. Assembling machines and bolting, welding, riveting or otherwise fastening them to a foundation or other structure by using hand tools and power tools; and
6. Repairing and lubricating machines and equipment (at the site of the public work) assembled and used by millwrights.

OPERATING ENGINEER, includes but is not limited to:

 Group 1
Bargeman
Blade Operator Assistant
Brakeman
Compressor Operator (when more than five (5) 900 CFM or larger
  units, additional Operator required)
Ditch Witch, with seat or similar type equipment
Elevator Operator - inside
Engineer Oiler
Forklift Operator  (under 5 Tons)
Generator Operator
Generator, Pump or Compressor Plant Operator
Pump Operator
Signalman
Steam Cleaner/Pressure Washer
Switchman

Group 2
Asphalt-Rubber Plant Operator (Nurse Tank Operator)
Concrete Mixer Operator - Skip type
Conveyor Operator
Fireman
Forklift Operator (over 5 Tons)
Hydrostatic Pump Operator
Oiler Crusher (Asphalt or Concrete Plant)
PJU Side Dump Jack
Rotary Drill Helper (Oilfield)
Screening and Conveyor Machine Operator (or similar types)
Skiploader (wheel type up to ¾ yd. without attachment)
Tar Pot Fireman
Temporary Heating Plant Operator
Trenching Machine Oiler

Group 3
Asphalt-Rubber Blend Operator
Bobcat or similar type (Skid Steer)
Equipment Greaser (rack)
Ford Ferguson (with dragtype attachments)
Helicopter Radioman (ground)
Stationary Pipe Wrapping and Cleaning Machine Operator

Group 4
Asphalt Plant Fireman
Backhoe Operator (Mini-Max or similar type)
Boring Machine Operator
Boring System Electronic Tracking Locator
Boxman or Mixerman (Asphalt or Concrete)
Chip Spreading Machine Operator
Concrete Cleaning Decontamination Machine Operator
Concrete Pump Operator (small portable)
Drilling Machine Operator, Small Auger Types (Texoma Super
  Economatic, or similar types - Hughes 100 or 200, or similar
  types - drilling depth of 30' maximum)
Equipment Greaser (Grease Truck)
Guard Rail Post Driver Operator
Highline Cableway Signalman
Horizontal Directional Drilling Machine
Hydra-Hammer-Aero Stomper
Micro Tunneling (above ground tunnel)
Power Concrete Curing Machine Operator
Power Concrete Saw Operator
Power - Driven Jumbo Form Setter Operator
Power Sweeper Operator
Roller Operator (compacting)
Screed Operator (Asphalt or Concrete)
Trenching Machine Operator (up to 6 ft.)
Vacuum or Muck Truck

Group 5
Equipment Greaser (Grease Truck/Multi-Shift)

Group 6
Articulating Material Hauler
Asphalt Plant Engineer
Batch Plant Operator
Bit Sharpener
Concrete Joint Machine Operator (canal and similar type)
Concrete Planer Operator
Dandy Digger
Deck Engine Operator
Derrickman (Oilfield type)
Drilling Machine Operator, Bucket or Auger Types (Calweld 100
  Bucket or similar types - Watson 1000 Auger or similar types -
  Texoma 330, 500 or 600 Auger or similar types - drilling depth
  of 45' maximum)
Drilling Machine Operator
Hydrographic Seeder Machine Operator (straw, pulp or seed)
Jackson Track Maintainer, or similar type
Kalamazoo Switch Tamper, or similar type
Machine Tool Operator
Maginnis Internal Full Slab Vibrator
Mechanical Berm, curb or gutter (concrete or asphalt)
Mechanical Finisher Operator (concrete, Clary-Johnson-Bidwell or
  similar)
Micro Tunnel System (below ground)
Pavement Breaker Operator (truck mounted, Oiler or Journeyman-
  trainee required)
Road Oil Mixing Machine Operator
Roller Operator (asphalt or finish)
Rubber-Tired Earth Moving Equipment (single engine, up to and
  including 25 yds. struck)
Self-Propelled Tar Pipelining Machine Operator
Skiploader Operator (crawler and wheel type, over ¾ yd. and up
  to and including 1½ yds.)
Slip Form Pump Operator (power driven hydraulic lifting device
  for concrete forms)
Tractor Operator - Bulldozer, Tamper-Scraper (single engine, up
  to 100 h.p. flywheel and similar types, up to and including
  D-5 and similar types)
Tugger Hoist Operator (1 drum)
Ultra High Pressure Waterjet Cutting Tool System Operator
Vacuum Blasting Machine Operator
Welder - General

Group 7
Welder - General (Multi-Shift)

Group 8
Asphalt or Concrete Spreading Operator (Tamping or Finishing)
Asphalt Paving Machine Operator (Barber Greene or similar type -
  1 Screed man required)
  Asphalt-Rubber Distributor Operator
Backhoe Operator (up to and including ¾ yd.) Small Ford, Case
  or similar.
Cast in Place Pipe Laying Machine Operator
Combination Mixer and Compressor Operator (Gunite Work)
Compactor Operator - self propelled
Concrete Mixer Operator - Paving (Oiler or Journeyman-trainee
  required)
Crushing Plant Operator (Oiler or Journeyman-trainee required)
Drill Doctor
Drilling Machine Operator, Bucket or Auger Types (Calweld 150
  Bucket or similar types - Watson 1500, 2000, 2500 Auger or
  similar types - Texoma 700, 800 Auger or similar types -
  drilling depth of 60' maximum)
Elevating Grader Operator
Grade Checker
Gradall Operator (Oiler or Journeyman-trainee required)
Grouting Machine Operator
Heavy Duty Repairman
Heavy Equipment Robotics Operator
Kalamazoo Balliste Regulator or similar type
Kolman Belt Loader and similar type (additional employee required
  on two (2) or more)
Le Tourneau Blob Compactor or similar type
Loader Operator (Athey, Euclid, Sierra and similar types)
Master Environmental Maintenance Mechanic
Ozzie Padder or similar types
PC 490 Slot Saw
Pneumatic Concrete Placing Machine Operator (Hackley-Presswell or
  similar type)
Pumpcrete Gun Operator
Rotary Drill Operator (excluding Caison type - Oiler or
  Journeyman-trainee required)
Rubber-Tired Earth Moving Equipment Operator (single engine,
  Caterpillar, Euclid, Athey Wagon, and similar types with any
  and all attachments over 25 yds. and up to and including
  50 cu. yds. struck)
Rubber-Tired Earth Moving Equipment Operator (multiple engine -
  up to and including 25 yds. struck)
Rubber-Tired Scraper Operator (self-loading paddle wheel type -
  John Deere, 1040 and similar single unit)
Self-Propelled Curb and Gutter Machine Operator
Shuttle Buggy
Skiploader Operator (crawler and wheel type over 1½ yds. up to
  and including 6½ yds.)
Soil Remediation Plant Operator (C.M.I. Enviro Tech Thermal or  Similar Types) (Oiler Required Group II)
Surface Heaters and Planer Operator
Tractor Compressor Drill Combination Operator
Tractor Operator (any type larger than D-5 - 100 flywheel h.p.
  and over, or similar -  Bulldozer, Tamper, Scraper and Push
  Tractor, single engine)
Tractor Operator (boom attachments)
Traveling Pipe Wrapping, Cleaning and Bending Machine Operator
Trenching Machine Operator (over 6 ft. depth capacity,
  manufacturer's rating - Oiler or Journeyman-trainee required)
Ultra High Pressure Waterjet Cutting Tool System Mechanic
Water Pull (compaction)

Group 9
Heavy Duty Repairman (Multi-Shift)

Group 10
Drilling Machine Operator, Bucket or Auger Types (Calweld 200 B
  Bucket or similar types - Watson 3000 or 5000 Auger or similar
  types - Texoma 900 Auger or similar types - drilling depth of
  105' maximum)
Dual Drum Mixer (Oiler or Journeyman-trainee required)
Heavy Duty Repairman-Welder Combination
Monorail Locomotive Operator (diesel, gas or electric)
Motor Patrol - Blade Operator (single engine)
Multiple Engine Tractor Operator (Euclid and similar type -
  except Quad 9 Cat.)
Pneumatic Pipe Ramming Tool and similar types
Pre-Stressed Wrapping Machine Operator (2 Operators required)
Rubber-Tired Earth Moving Equipment Operator (single engine, over
  50 yds. struck)
Rubber-Tired Earth Moving Equipment Operator (multiple engine,
  Euclid, Caterpillar and similar - over 25 yds. and up to
  50 yds. struck)
Tower Crane Repairman
Tractor Loader Operator (crawler and wheel-type over 6½ yds.)
Welder-Certified
Woods Mixer Operator (and similar Pugmill equipment)

Group 11
Dynamic Compactor LDC350 (or similar types - two (2) Operators
  required)
Heavy Duty Repairman-Welder Combination (Multi-Shift)
Welder-Certified (Multi-Shift)

Group 12
Auto Grader Operator (Grade Checker and one (1) additional
  employee required)
Automatic Slip Form Operator (Grade Checker and one (1)
  additional employee required.)
Drilling Machine Operator, Bucket or Auger Types (Calweld, Auger
  200 CA or similar types - Watson, Auger 6000 or similar types-
  Hughes Super Duty, Auger 200 or similar types - drilling depth
  of 175' maximum)
Hoe Ram or similar with Compressor
Mass Excavator Operator - Less than 750 cu. yds. (two (2)
  Operators and Oiler or Journeyman-Trainee required)
Mechanical Finishing Machine Operator
Mobile Form Traveler Operator
Motor Patrol Operator (multi-engine)
Pipe Mobile Machine Operator (two (2) Operators required)
Rubber-Tired Earth Moving Equipment Operator (multiple engine,
  Euclid, Caterpillar and similar type, over 50 cu. yds. struck)
Rubber-Tired Self-Loading Scraper Operator (paddle-wheel-Auger
  type self-loading - two (2) or more units)
Vermeer Rock Trencher (or similar type)

Group 13
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Push-Pull System (single engine, up to and including
  25 yds. struck)

Group 14
Canal Liner Operator (not less than four (4) employees -
  Operator, Oiler, Welder, Mechanic, Grade Checker required)
Canal Trimmer Operator (Operator, Oiler, and two (2) other
  employees covered by these provisions  required)
Remote Controlled Earth Moving Equipment Operator (no one (1)
  Operator shall operate more than two (2) pieces of earth
  moving equipment at one time - One Dollar ($1.00) per hour
  additional to base rate)
Wheel Excavator Operator (over 750 cu. yds. per hour - two (2)
  Operators and one (1) Oiler or Journeyman-trainee, and two (2)
  Heavy Duty Repairmen required)

Group 15
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Push-Pull System (single engine, Caterpillar, Euclid,
  Athey Wagon, and similar types with any and all attachments
  over 25 yds. and up to and including 50 cu. yds. struck)
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Push-Pull System (multiple engine - up to and
  including 25 yds. struck)

Group 16
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Push-Pull System (single engine, over 50 yds. struck)
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Push-Pull System (multiple engine, Euclid,
  Caterpillar and similar, over 25 yds. and up to 50 yds. struck)

Group 17
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Push-Pull System (multiple engine, Euclid,
  Caterpillar and similar type, over 50 cu. yds. struck)
Tandem Tractor Operator (operating crawler type tractors in
  tandem - Quad 9 and similar type)

Group 18
Rubber-Tired Earth Moving Equipment Operator, operating in Tandem
  (scrapers, belly dumps, and similar types in any combination,
  excluding compaction units - single engine, up to and
  including 25 yds. struck)

Group 19
Rotex Concrete Belt Operator (or similar types)
Rubber-Tired Earth Moving Equipment Operator, operating in Tandem
  (scrapers, belly dumps, and similar types in any combination,
  including compaction units - single engine, Caterpillar,
  Euclid, Athey Wagon, and similar types with any and all
  attachments over 25 yds. and up to and including 50 cu. yds.
  struck)

Rubber-Tired Earth Moving Equipment Operator, operating in Tandem
  (scrapers, belly dumps, and similar types in any combination,
  excluding compaction units - multiple engine, up to and
  including 25 yds. struck)

Group 20
Rubber-Tired Earth Moving Equipment Operator, operating in Tandem
  (scrapers, belly dumps, and similar types in any combination,
  excluding compaction units - single engine, over 50 yds. struck)
Rubber-Tired Earth Moving Equipment Operator, operating in Tandem
  (scrapers, belly dumps, and similar types in any combination,
  excluding compaction units - multiple engine, Euclid,
  Caterpillar and similar, over 25 yds. and up to 50 yds. struck)

Group 21
Rubber-Tired Earth Moving Equipment Operator, operating in Tandem
  (scrapers, belly dumps, and similar types in any combination,
  excluding compaction units - multiple engine, Euclid,
  Caterpillar and similar type, over 50 cu. yds. struck)

Group 22
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Tandem Push-Pull System (single engine, up to and
  including 25 yds. struck)

Group 23
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Tandem Push-Pull System (single engine, Caterpillar,
  Euclid, Athey Wagon, and similar types with any and all
  attachments over 25 yds. and up to and including 50 cu. yds.
  struck)
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Tandem Push-Pull System (multiple engine, up to and
  including 25 yds. struck)

Group 24
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Tandem Push-Pull System (single engine, over 50 yds.
  struck)
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Tandem Push-Pull System (multiple engine, Euclid,
  Caterpillar and similar, over 25 yds. & up to 50 yds. struck)

Group 25
Concrete Pump Operator - truck mounted (Oiler required when boom
  over 105' or 36 meters)
Rubber-Tired Earth Moving Equipment Operator, operating equipment
  with the Tandem Push-Pull System (multiple engine, Euclid,
  Caterpillar and similar type, over 50 cu. yds. struck)
 

OPERATING ENGINEER-CRANES, PILEDRIVING AND HOISTING EQUIPMENT 

Group1
Engineer Oiler
Forklift Operator

Group 2
Truck Crane Oiler

Group 3
A-Frame or Winch Truck Operator
Ross Carrier Operator (jobsite)

Group 4
Bridge-Type Unloader and Turntable Operator
Helicopter Hoist Operator

Group 5
Hydraulic Boom Truck (Pitman)
Stinger Crane (Austin-Western or similar type)
Tugger Hoist Operator (1 drum)

Group 6
Bridge Crane Operator
Cretor Crane Operator (Oiler required)
Hoist Operator (Chicago Boom and similar type)
Lift Mobile Operator (Oiler required)
Lift Slab Machine Operator (Vagtborg and similar types)
Material Hoist/Manlift Operator
Polar Gantry Crane Operator
Self Climbing Scaffold (or similar type)
Shovel, Backhoe, Dragline, Clamshell Operator (over ¾ yd. and
  up to 5 cu. yds. M.R.C., Oiler required)
Tugger Hoist Operator (2 drum)

Group 7
Pedestal Crane Operator
Shovel, Backhoe, Dragline, Clamshell Operator (over 5 cu. yds,
  M.R.C., Oiler required)
Tower Crane Repairman
Tugger Hoist Operator (3 drum)

Group 8
Crane Operator (up to and including 25 ton capacity, see Crew
  Size Requirement)
Crawler Transporter Operator
Derrick Barge Operator (up to and including 25 ton capacity, see
  Crew Size Requirement)
Hoist Operator, Stiff Legs, Guy Derrick or similar type (up to and
  including 25 ton capacity, see Crew Size Requirement)
Shovel, Backhoe, Dragline, Clamshell Operator (over 7 cu. yds,
  M.R.C., Oiler required)

Group 9
Crane Operator (over 25 tons, up to and including 50 ton M.R.C.,
  see Crew Size Requirement)
Derrick Barge Operator (over 25 tons, up to and including 50 ton
  M.R.C., see Crew Size Requirement)
Highline Cableway Operator
Hoist Operator, Stiff Legs, Guy Derrick or similar type (over 25
  tons, up to and including 50 ton M.R.C., see Crew Size
  Requirement)
K-Crane
Polar Crane Operator
Self-Erecting Tower Crane Operator Maximum Lifting Capacity ten (10) tons.  One (1) ton operator).

Group 10
Crane Operator (over 50 tons, up to and including 100 ton M.R.C.,
  Oiler required)
Derrick Barge Operator (over 50 tons, up to and including 100 ton
  M.R.C., see Crew Size Requirement)
Hoist Operator, Stiff Legs, Guy Derrick or similar type (over 50
  tons, up to and including 100 ton M.R.C., see Crew Size
  Requirement)
Mobile Tower Crane Operator (over 50 tons, up to and including
  100 ton M.R.C., two (2) Operators required)
Tower Crane Operator and Tower Gantry (see Crew Size Requirement)

Group 11
Crane Operator (over 100 tons, up to and including 200 ton
  M.R.C., Oiler required)
Derrick Barge Operator (over 100 tons, up to and including 200
  ton M.R.C., see Crew Size Requirement)
Hoist Operator, Stiff Legs, Guy Derrick or similar type (over 100
  tons, up to and including 200 ton M.R.C., see Crew Size
  Requirement)
Mobile Tower Crane Operator (over 100 tons, up to and including
  200 ton M.R.C., two (2) Operators required)

Group 12
Crane Operator (over 200 tons, up to and including 300 ton
  M.R.C., Oiler required)
Derrick Barge Operator (over 200 tons, up to and including 300
  ton M.R.C., see Crew Size Requirement)
Hoist Operator, Stiff Legs, Guy Derrick or similar type (over 200
  tons, up to and including 300 ton M.R.C., see Crew Size
  Requirement)
Mobile Tower Crane Operator (over 200 tons, up to and including
  300 ton M.R.C., two (2) Operators required)

Group 13
Crane Operator (over 300 tons, two (2) Operators required)
Derrick Barge Operator (over 300 tons, see Crew Size Requirement)
Helicopter Pilot
Hoist Operator, Stiff Legs, Guy Derrick or similar type (over 300
  tons, see Crew Size Requirement)
Mobile Tower Crane Operator (over 300 tons, two (2) Operators
  required)

OPERATING ENGINEER-Tunnel 

Group 1
Heavy Duty Repairman Helper

Group 2
Skiploader (wheel type up to ¾ yd. without attachment)

Group 3
Chainman
Power - Driver Jumbo Form Setter Operator

Group 4
Dinkey Locomotive or Motorman (up to and including 10 tons)
Rodman

Group 5
Bit Sharpener
Equipment Greaser (Grease Truck)
Instrumentman
Slip Form Pump Operator (power driven hydraulic lifting device
  for concrete forms)
Tugger Hoist Operator (1 drum)
Tunnel Locomotive Operator (over 10 and up to and including 30
  tons)
Welder - General

Group 6
Backhoe Operator (up to and including ¾ yd.) Small Ford, Case
  or similar
Drill Doctor
Grouting Machine Operator
Heading Shield Operator
Heavy Duty Repairman
Loader Operator (Athey, Euclid, Sierra and similar types)
Mucking Machine Operator (¼ yd. - Oiler or Journeyman-trainee
  required - rubber-tired, rail or track type)
Pneumatic Concrete Placing Machine Operator (Hackley-Presswell or
  similar type)
Pneumatic Heading Shield (tunnel)
Pumpcrete Gun Operator
Tractor Compressor Drill Combination Operator
Tugger Hoist Operator (2 drum)
Tunnel Locomotive Operator (over 30 tons)

Group 7
Heavy Duty Repairman-Welder Combination

Group 8
Party Chief

Group 9
Certified Chief of Party
Tunnel Mole Boring Machine Operator

PAINTER, includes but is not limited to:

1. All painting of walls, equipment, buildings, bridges and other structural surfaces by using brushes, rollers and spray guns;
2. Application of wall coverings/wall paper;
3. Removing old paint to prepare surfaces before painting the surface;
4. Mixing colors or oils to obtain desired color or consistency;
5. Sanding surfaces between coats and polishing final coat to a specified finish;
6. Cutting stencils and brushing and spraying lettering and decorations on surfaces;
7. Washing and treating surfaces with oil, turpentine, mildew remover or other preparations;
8. Filling cracks, holes and joints with caulk, putty, plaster or other filler by using caulking gun or putty knife;

PILEDRIVER, includes but is not limited to:

1. Operating pile drivers mounted on skids, barge, crawler, treads or locomotive crane to drive piling as foundations for structures including, without limitation, buildings, bridges and piers;
2. Barking, shoeing, splicing, form building, heading, centering, placing, driving, staying, framing, fastening, automatic pile threading, pulling and/or cutting off of piling;
3. Fabricating, forming, handling and setting of all such pre-cast, pre-stressed and post-stressed shapes that are an integral part of docks, piers, wharves, bulkheads, jetties, and similar structures;

PIPEFITTER, includes but is not limited to:

Assembling, installing, modifying and maintaining pipe systems, pipe supports and pneumatic equipment and related machines and equipment components for steam, hot water, heating, cooling, lubricating, sprinkling and industrial and processing systems which may require:

1. Cutting, threading and hammering pipe to specifications using tools, including, without limitation, saws, cutting torches and pipe threaders and benders;
2. Attaching pipes to walls, structures and fixtures, including without limitation, radiators or tanks, using brackets, clamps, tools, or welding equipment;
3. Coating non-ferrous piping materials by dipping in mixture of molten tin and lead to prevent erosion, or galvanic and electrolytic action;

PLASTERER, includes but is not limited to:

1. Applying coats of plaster onto interior or exterior walls, ceilings, or partitions of buildings to produce a finished surface according to blueprints, architects' drawings and oral instruction;
2. Creating decorative textures in finish coat by using sand, pebbles or stones;
3. Installing guide wires on exterior surfaces of buildings to indicate thickness of plaster or stucco;
4. Applying weatherproof, decorative covering to exterior surfaces of a building;
5. Molding and installing ornamental plaster pieces, panels and trim;
6. Directing workers to mix plaster to a desired consistency;
7. Assembly of EFIS panels;
8. Laying out, cutting, joining, fitting and installation of Architectural Foam Elements which are trowel applied or adhesive set;
9. Applying, shaping, cutting, and planing in preparation for netting done by hand or machine;
10. All plaster or synthetic finishes applied to Foam Architectural Elements

PLUMBER, includes but is not limited to:

Assembling, installing and repairing pipes, fittings and fixtures for heating, water and drainage systems inside of buildings and to a point 5 feet outside of buildings which may therein require:

1. Repairing and maintaining plumbing by replacing defective washers, repairing or mending broken pipes, and opening clogged drains;
2. Assembling pipe sections, tubing and fittings by using screws, bolts, solder, plastic solvent and caulking;
3. Installing pipe assemblies, fittings, valves and fixtures, including, without limitation, sinks, toilets and tubs, by using hand tools and power tools;
4. Cutting openings in structures, excluding concrete, to accommodate pipe and pipe fittings by using hand tools and power tools;
5. Filling pipes and plumbing fixtures with water or air and observing pressure gauges to detect and locate leaks.

REFRIGERATION MECHANIC, includes but is not limited to:

1. Installing and repairing industrial and commercial refrigeration systems;
2. Mounting compressors, condensers and other refrigeration components to the frame of a refrigerator by using hand tools and acetylene welding equipment;
3. Assembling structural and functional components needed for refrigeration, including, without limitation, controls, switches, gauges, wiring harnesses, valves, pumps, compressors, condensers, cores and pipes;
4. Installing expansion and control valves by using hand tools and acetylene welding equipment;
5. Cutting, bending, threading and connecting pipe from functional components to water, power or refrigeration systems;
6. Fabricating and assembling components and structural portions of a refrigeration system;

ROOFER, includes but is not limited to:

1. Installing and covering roofs and structures with slate, asphalt, wood and other related materials, other than sheet metal, by using brushes, knives, punches, hammers and other tools;
2. Spraying roofs, sidings and walls with material to bind, seal, insulate or soundproof sections of a structure;
3. Installation of all plastic, slate, slag, gravel, asphalt and composition roofing, and rock asphalt mastic when used for damp and waterproofing;
4. Installation of all damp resisting preparations when applied on roofs with mop, three-knot brush, roller, swab or spray system;
5. All types of preformed panels used in waterproofing;
6. Handling, hoisting and storing of all roofing, damp and waterproofing materials;
7. The tear-off and/or removal of roofing and roofing materials;

SHEET METAL WORKER, includes but is not limited to:

1. Fabricating, assembling, dismantling, installing or repairing:
   • Sheet metal roofs, including #30 felt roofing paper installed to form a metal roofing system;
   • Sheet metal parts or equipment, including, without limitation, duct work, metal lockers and kitchen equipment;
   • Air-veyor and air-handling systems, regardless of materials used;
2. Setting up and operating fabrication machines to cut, bend and straighten sheet metal;
3. Shaping metal over anvils, blocks or forms using a hammer;
4. Operating soldering and welding equipment to join sheet metal parts;
5. Inspecting, assembling and smoothing seams and joints of burred surfaces;
6. Welding, soldering, bolting, riveting, screwing, clipping, caulking or bonding component parts to assemble products by using hand tools, power tools and devices for lifting and handling;

SPRINKLER FITTER, includes but is not limited to:

Installing, dismantling, maintaining, repairing, adjusting and correcting all fire protection and fire control systems, including the installation of piping or tubing, appurtenances and equipment pertaining thereto, including both overhead and underground water mains, fire hydrants, and hydrant mains, standpipes and hose connection to sprinkler systems, sprinkler tank heaters, air lines and thermal systems used in connection with sprinkler and alarm systems.

SURVEYOR, includes but is not limited to:

1. Planning ground surveys designed to establish base lines, elevation and other geodetic measurements;
2. Compiling data relevant to the shape, contour, gravitation, location, elevation and dimension of land and land features on or near the surface of the Earth for engineering, map making, mining, land evaluation, construction and other purposes;
3. Surveying bodies of water to determine navigable channels and to secure data for construction of breakwaters, piers and other marine structures;
4. Computing data necessary for driving and connecting underground passages, underground storage and volume of underground deposits.

SURVEYOR

Group 1

Chainman

Group 2

Rodman

Group 3

Instrumentman

Group IV

Global Position Systems Chainman and Rodman

Hydrographic Engineering Technician I (Chainman)

Group V

Party Chief

Group VI

E.D.M. or Fathometer Instrumentman

Group VII

Certified Party Chief

Group VIII

Hydrographic Engineer Party Chief

Group IX

Certified Hydrographic Engineer Party Chief

Global Position Systems Party Chief

Group X

Chief of Parties

Two (2) or more crews 

TAPER, includes but is not limited to:

1. Sealing joints between plasterboard or other wallboards to prepare a wall surface for painting or papering;
2. Mixing sealing compound by hand or with a portable electric mixer and spreading the compound over the joints between boards using a trowel, broad knife, or spatula;
3. Filling cracks and holes in walls and ceilings with sealing compound ;
4. Applying texturing compound and primer to walls and ceiling to prepare a surface for a final finish by using brushes, rollers and spray guns;
5. Coating of joint compound or taping mud;

TERRAZZO WORKER, includes but is not limited to:

1. Applying cement, sand, pigment and marble chips to floors and stairways to attain durable and decorative surfacing according to specifications or drawings;
2. Spreading mixtures of sand, cement and water over surface with a trowel to form terrazzo;
3. Cutting metal division strips and pressing the metal division strips into a terrazzo base so that top edges form a desired design or pattern and define level of finished floor surface;
4. Spreading mixtures of marble chips, cement, pigment and water over a terrazzo base to form a finished surface by using a float and trowel;
5. Pre-casting terrazzo blocks in wooden forms.

TILE SETTER, includes but is not limited to:

1. Applying tile and materials made for tile in tile-like units to walls, floors, ceilings and promenade roof decks following design specification;
2. Applying glazed, unglazed, mosaic and other ceramic tiles, which are used as a surface on floors, walls, ceilings, and other surfaces and which must be set to specific grade;
3. Applying and floating all setting beds into which glazed, unglazed, mosaic, or other ceramic tiles are set;
4. Leveling and plumbing tiles to a specified grade.

TILE, TERRAZZO AND MARBLE FINISHER, includes but is not limited to:

1. Supplying and mixing construction materials for a tile setter, terrazzo worker or marble setter;
2. Applying grout and finishing the surface of installed tile, terrazzo and marble;
3. Cleaning installed tile, terrazzo and tile surfaces;
4. Renovation and filling chipped, cracked and broken pieces of tile, terrazzo and marble;
5. Grinding and polishing tile, terrazzo and marble;
6. Assisting a tile setter, terrazzo worker or marble setter;

TRAFFIC BARRIER ERECTOR, includes but is not limited to:

Erects or places instruments to provide directional assistance to traffic on or near the public works construction project.

TRUCK DRIVER, includes but is not limited to:

Group 1
Drivers of dump trucks (less than 12 yds. water level), drivers of trucks (legal payload capacity less than 15 tons), water and fuel truck drivers under 2,500 gal, pickup driver, service truck driver, teamster equipment (highest rate paid for dual craft operation),  drivers of busses on site used for transportation of up to twenty-five (25) passengers, working flat rack driver.

Group 2
Drivers of dump trucks (12 yds but less than 16 yds water level), drivers of trucks (legal payload capacity between 15 and 20 tons), drivers of transit mix trucks (under 3 yds), dumpcrete trucks (less than 6 ½ yds water level), gas and oil pipeline working truck drivers, including winch truck and all sizes of trucks, water and fuel truck drivers (2,500 gal to 4,000 gal), truck greaser, drivers of busses (on jobsite used for transportation or more than twenty-five (25) passengers).

Group 3
Drivers of dump trucks (16 yds up to and including 22 yds water level), drivers of trucks (legal payload cap. 20 tons but less than 30 tons), drivers of dumpster trucks, drivers of transit-mix trucks (3 yds but less than 6 yds), dumpcrete trucks (6 ½ yds water level and over), fork lift driver, Ross Carrier driver, highway water and fuel drivers (4,000 gal but less than 6,000 gal),  tire man.

Group 4
Drivers of transit-mix trucks (6 yds or more), drivers of dump trucks (over 22 yds. water level), drivers of trucks (legal payload capacity 30 tons and over) drivers of fuel and water trucks (6,000 gal and over)

Group 5
Drivers of trucks and trailers in combination (seven axles or more)

Group 6
All Off-road Equipment, Truck Repairman, and Drivers of Road Oil Spreader Trucks

DW 10 and DW 20 Euclid-type equipment Letourneau pulls, Terra Cobras and similar types of equipment, also PB and similar type trucks performing work within the Teamster jurisdiction, regardless of types of attachment, including power units pulling off-highway belly dumps in tandem

All off-road equipment for the purposes of these provisions, shall mean any equipment or combination of unladen equipment which cannot be licensed for normal or regular highway use because of width, height or length limitations when measuring the equipment or combination as it is being operated.
 
 

WELL DRILLER, includes but is not limited to:

1. Setting, operating or tending to portable drilling rig machinery and related equipment to drill wells;
2. Extending stabilizing jackscrews to support and level a drilling rig;
3. Installing water well pumps;
4. Drillings wells for industrial water supplies, irrigation water supplies or water supplies for any other purpose; dewatering or other similar purposes; exploration; hole drilling for geologic and hydrologic information; and core drilling for geologic information.

ZONE RATES

BRICKLAYER
In addition to BRICKLAYER rates add the applicable amounts  per hour, calculated based on a radius of over fifty (50) miles from the City Hall of Las Vegas, Nevada:
0-50 Miles                        Free Zone
51-70 Miles                      $18.00 per day
Over 70 Miles                   $38.00 per day

The area within the city limits of Boulder City and Primm, Nevada shall be considered free zones. 

CARPENTER
In addition to CARPENTER rates add the applicable amounts  per hour, calculated based on a radius from Maryland Parkway and Charleston Boulevard, Las Vegas:
Zone 1-0 to 30 miles         0.00
Zone 2-30 to 50 miles       1.50
Zone 3-Over 50 miles       3.25

CEMENT MASON
In addition to CEMENT MASON rates add the applicable amounts per hour, calculated based on a radius from City Hall of Las Vegas:
Zone 1-0 to 20 miles      0.00
Zone 2-20 to 40 miles    1.50
Zone 3-40 to 60 miles    2.50
Zone 4-Over 60 miles    3.00

 

ELECTRICIAN COMMUNICATION TECHNICIAN
In addition to ELECTRICIAN-Electronic Communication Technician rates add the applicable amounts per hour, calculated based on a radius from City Hall of Las Vegas:
Zone 1  0-25  miles	0.00
Zone 2 25-55 miles	1.50
Zone 3 55 miles and over	2.50

ELECTRICIAN-LINEMAN
In addition to ELECTRICIAN-Lineman/Groundman/Heavy Equipment Operator rates  add the applicable amounts per hour, calculated based on a radius from City Hall of  Las Vegas:
Zone 1-0 to 30 miles         0.00
Zone 2-30 miles and over  1.50

ELECTRICIAN-WIREMAN
In addition to ELECTRICIAN-Wireman rates  add the applicable amounts per hour, calculated based on a radius from City Hall of  Las Vegas:
Zone 1-0 to 25 miles         0.00
Zone 2-25 to 55 miles       1.50
Zone 3-55  miles and over 2.50

LABORER
In addition to Laborer rates add the applicable amounts per hour, calculated based on a radius from City Hall of  Las Vegas:                                                                       
Zone 1-0 to 30 Miles          0.00
Zone 2-30 to 50 Miles        1.50
Zone 3-50 to 70 Miles        2.50
Zone 4-Over 70 Miles        3.00
Laughlin Area                      2.25

MILLWRIGHT
In addition to MILLWRIGHT rates add the applicable amounts  per hour, calculated based on a radius from Maryland Parkway and Charleston Boulevard, Las Vegas:
Zone 1-0 to 20 miles         0.00
Zone 2-20 to 40 miles       1.50
Zone 3-40 miles and over  3.25

OPERATING ENGINEER
In addition to: OPERATING ENGINEER; CRANES, PILEDRIVING AND HOISTING EQUIPMENT; TUNNEL  AND SURVEYOR rates add the applicable amounts per hour calculated from Las Vegas City Hall:
Zone 1-0 to 20 miles         0.00
Zone 2-20 to 40 miles       1.50
Zone 3-40 to 60 miles       2.50
Zone 4-over 60 miles        3.00

PLASTERER
In addition to PLASTERER rates add the applicable amounts per hour, calculated from the city hall of Las Vegas, Nevada:
Zone 1-0 to 20 miles         0.00
Zone 2-20 to 40 miles       1.50
Zone 3-40 to 60 miles       2.50
Zone 4-over 60 miles        3.00

SHEET METAL WORKER
In addition to SHEET METAL WORKER rates add the applicable amounts per hour, calculated on a radius from Las Vegas City Hall:
Zone 1-0 to 25 miles        0.00
Zone 2-25 to 50 miles      2.00
Zone 3-50 to 100 miles    3.00
Zone 4-over 100 miles     4.50

TILE/TERRAZZO WORKER/MARBLE MASON
In addition to TILE/TERRAZZO WORKER/MARBLE MASON rates add the applicable amounts  per hour, calculated based on a radius of over fifty (50) miles from the City Hall of Las Vegas, Nevada:
0-50 Miles                        Free Zone
51-70 Miles                      $18.00 per day
Over 70 Miles                   $38.00 per day

The area within the city limits of Boulder City and Primm, Nevada shall be considered free zones. 

TRUCK DRIVER
In addition to TRUCK DRIVER rates add the applicable amounts per hour, calculated from Las Vegas City Hall:
Zone 1-0 to 30 miles         0.00
Zone 2-30 to 50 miles       1.00
Zone 3-50 to 70 miles       2.00
Zone 4-70 to 80 miles       3.00
Zone 5-Over 80 Miles       3.50
Laughlin & Mesquite         3.00